Currently my experience with 3D printing. It’s one thing after another, and the community, at least on Reddit and Facebook, fucking sucks. If I ask a question, it’s always “hey how about you go fuck yourself” or an essay that has zero relevance to what I’m asking. Made a post on Reddit the other day (I know, but have a single burner account until the 3D printing community here takes off more) and just asked to see some settings due to just constantly having issue after issue. Half of the responses were people just telling me they’re not fucking wizards and they need to know what kind of problems I’m having. I… didn’t ask for that whatsoever. I very explicitly just asked for someone’s slicer settings to compare to.
That’s absolutely the worst help forum experience, when you’re asking one question but everyone extrapolates the question they think you REALLY meant to ask and talks down to you about it.
And of course if you try to steer the conversation back to your actual question, you get painted as the unreasonable one placing all sorts of conditions on the generous free help others are allowed to bestow upon you.
The less reliance on others Linux requires, the better off it will be for general adoption.
Haha your second paragraph sums it up perfectly. A few folks did share their settings, but they were for completely different printers/hardware haha. Most of the online guides I’ve found are written under the assumption that you’re already a master at the hobby, and it’s strangely spread out in random little nooks of the internet - there’s not really a ton of centralized discussion forums. Maybe the hobby is way smaller than I thought, or maybe I’m just in way over my head, but I fix tech problems for a living - did not expect this to be as much of a challenge. Never buy a 3D printer if you value your sanity and living stress-free. Sorry, I just needed to rant for a minute haha.
Yeah 3D printers are fussier than I expected. Especially when printing anything involving supports and more specifically… small areas that need supports. I print a lot of stuff for D&D and have just started cutting things up into pieces with blender to print easier, then glue it together
I will say. My first thought was obviously to ask what printer you have, to see if I could send you my profile for you to compare (depending on the slicer you use). Then my second was to ask if you’re having issues and if so, what the issues are.
Only because sometimes a seemingly large issue could be a very small fix.
When I first started, I got it working great and then out of no where nothing would stick to the bed. I spent more time than I’d like to admit messing with settings only to realize it was the oils on my hands causing adhesion issues. Some 99% IPA fixed all my issues real quick haha.
That would be awesome! I’ve got an Ender 6 with a Micro Swiss NG extruder. I was printing decently with the stock hardware, but that stock extruder was a nightmare and kept slipping or completely losing grip on filament mid-print, so I upgraded to this extruder. Now I’m just trying to find that perfect spot to where it extrudes but doesn’t grind filament. I’ve been having some really messy prints.
I just had a feeler gauge arrive in the mail, so I’m about to use that to try leveling the bed more accurately. Everyone says to just use a piece of paper or something, but different paper is different widths haha.
I do have a PEI bed, so stuff sticks and comes off way easier now, but I would love to check out your slicer settings to get a good baseline! What kind of hardware do you have, and which slicer do you use?
Just using that outright probably won’t work. What I would do is load up the default Ender 6 profile that Cura has, and then adjust settings based on mine. For instance. You went from a bowden extruder to a direct drive. So you can probably copy my retraction settings as a baseline and adjust from there. You need far less retraction on direct drive extruders (i.e. 0.2mm-1mm for direct drive vs 5mm-8mm for bowden).
I would also look up CHEP and Teaching Tech on youtube. They have great videos on bed leveling and everything else related to 3d printing.
Most of the online guides I’ve found are written under the assumption that you’re already a master at the hobby
I’ve had exactly the opposite experience lol. Most of the stuff out there is dreadfully basic, and if you want detail like scientific comparisons of the strength-weight ratios of different infill patterns, good fuckin luck. Some chum on YouTube will have some half baked experiments and that’s as good as it gets.
Currently my experience with 3D printing. It’s one thing after another, and the community, at least on Reddit and Facebook, fucking sucks. If I ask a question, it’s always “hey how about you go fuck yourself” or an essay that has zero relevance to what I’m asking. Made a post on Reddit the other day (I know, but have a single burner account until the 3D printing community here takes off more) and just asked to see some settings due to just constantly having issue after issue. Half of the responses were people just telling me they’re not fucking wizards and they need to know what kind of problems I’m having. I… didn’t ask for that whatsoever. I very explicitly just asked for someone’s slicer settings to compare to.
That’s absolutely the worst help forum experience, when you’re asking one question but everyone extrapolates the question they think you REALLY meant to ask and talks down to you about it.
And of course if you try to steer the conversation back to your actual question, you get painted as the unreasonable one placing all sorts of conditions on the generous free help others are allowed to bestow upon you.
The less reliance on others Linux requires, the better off it will be for general adoption.
Haha your second paragraph sums it up perfectly. A few folks did share their settings, but they were for completely different printers/hardware haha. Most of the online guides I’ve found are written under the assumption that you’re already a master at the hobby, and it’s strangely spread out in random little nooks of the internet - there’s not really a ton of centralized discussion forums. Maybe the hobby is way smaller than I thought, or maybe I’m just in way over my head, but I fix tech problems for a living - did not expect this to be as much of a challenge. Never buy a 3D printer if you value your sanity and living stress-free. Sorry, I just needed to rant for a minute haha.
Yeah 3D printers are fussier than I expected. Especially when printing anything involving supports and more specifically… small areas that need supports. I print a lot of stuff for D&D and have just started cutting things up into pieces with blender to print easier, then glue it together
I will say. My first thought was obviously to ask what printer you have, to see if I could send you my profile for you to compare (depending on the slicer you use). Then my second was to ask if you’re having issues and if so, what the issues are.
Only because sometimes a seemingly large issue could be a very small fix.
When I first started, I got it working great and then out of no where nothing would stick to the bed. I spent more time than I’d like to admit messing with settings only to realize it was the oils on my hands causing adhesion issues. Some 99% IPA fixed all my issues real quick haha.
That would be awesome! I’ve got an Ender 6 with a Micro Swiss NG extruder. I was printing decently with the stock hardware, but that stock extruder was a nightmare and kept slipping or completely losing grip on filament mid-print, so I upgraded to this extruder. Now I’m just trying to find that perfect spot to where it extrudes but doesn’t grind filament. I’ve been having some really messy prints.
I just had a feeler gauge arrive in the mail, so I’m about to use that to try leveling the bed more accurately. Everyone says to just use a piece of paper or something, but different paper is different widths haha.
I do have a PEI bed, so stuff sticks and comes off way easier now, but I would love to check out your slicer settings to get a good baseline! What kind of hardware do you have, and which slicer do you use?
Sure thing, I have a two Sovol SV06’s, one for a 0.4 nozzle and one for a 0.2 nozzle, and a Bambu Labs X1C.
The SV06’s took me a few weeks to tweak, especially the one with the 0.2 nozzle.
Here is my cura profile for the Sovol SV06 with the 0.4 nozzle https://filebin.net/ljh52w2lehipzbms
Just using that outright probably won’t work. What I would do is load up the default Ender 6 profile that Cura has, and then adjust settings based on mine. For instance. You went from a bowden extruder to a direct drive. So you can probably copy my retraction settings as a baseline and adjust from there. You need far less retraction on direct drive extruders (i.e. 0.2mm-1mm for direct drive vs 5mm-8mm for bowden).
I would also look up CHEP and Teaching Tech on youtube. They have great videos on bed leveling and everything else related to 3d printing.
I’ve had exactly the opposite experience lol. Most of the stuff out there is dreadfully basic, and if you want detail like scientific comparisons of the strength-weight ratios of different infill patterns, good fuckin luck. Some chum on YouTube will have some half baked experiments and that’s as good as it gets.